Inquiry Basket ( 0 )
Company Details
  • Yangzhou Yinhe Machinery Co., Ltd

  •  [Jiangsu,China]
  • Business Type:Manufacturer
  • Main Markets: Africa , Americas , Asia , Caribbean , East Europe , Europe , Middle East , North Europe , Oceania , Other Markets , West Europe , Worldwide
  • Exporter:21% - 30%
  • Certs:ISO9001
Yangzhou Yinhe Machinery Co., Ltd

Yangzhou Yinhe Machinery Co., Ltd

Home > News > The Latest Twelve Major Considerations When Installing and Disassembling the Hydraulic Cylinder

News

The Latest Twelve Major Considerations When Installing and Disassembling the Hydraulic Cylinder

2015-10-10

1) Before the hydraulic cylinder is disassembled, the hydraulic circuit should be depressurized. Otherwise, the high-pressure oil in the circuit will be quickly sprayed when the tubing connection with the cylinder is loosened. When the hydraulic circuit is depressurized, loosen the handwheel or pressure adjusting screw at the overflow valve to unload the pressure oil, then cut off the power or cut off the power source to stop the hydraulic device.



2)When disassembling, damage to the top of the piston rod, the threads of the piston rod, the surface of the piston rod, and the inner wall of the cylinder liner should be prevented. In order to prevent bending or deformation of the elongate member such as the piston rod, a balance of wood support is applied when placing.

3)Disassemble it in order. Because the structure and size of various hydraulic cylinders are not the same, the disassembly sequence is slightly different. Generally, the two-chamber oil should be drained, then the cylinder head removed, and finally the piston and piston rod removed. When disassembling the cylinder head of a hydraulic cylinder, special tools are used for the card key or snap ring of the internal card key type connection. The use of a flat spatula is prohibited. For the flange type end cap, it must be screwed out. Hammering or hard hammering is not allowed. When pistons and piston rods are difficult to withdraw, they must not be forcibly ejected. They should be identified and disassembled.


4)Before and after unloading, try to create conditions to prevent the parts of the hydraulic cylinder from being contaminated by dust and impurities around it. For example, it should be done in a clean environment as far as possible; all parts should be covered with plastic cloth after disassembly, and do not cover with cotton cloth or other working cloths.


5) After the cylinder is disassembled, it must be checked carefully to determine which parts can be used continuously, which parts can be used after repairs, and which parts must be replaced.



6)The parts must be carefully cleaned before assembly.



7) Properly install the seals throughout.

When installing the O-ring, do not pull it to the degree of permanent deformation, do not roll the edge of the package, or it may leak due to the formation of a twist.

When installing the Y-shaped and V-shaped sealing rings, pay attention to the installation direction to avoid oil leakage due to the installation. For Y-ring seals, the lip of the Y-ring seals against the pressure of the oil chamber. In addition, the Yx-ring seal must also be used to distinguish between the shaft and the hole. Do not install the wrong seal. The V-shaped seal ring is composed of a support ring, a seal ring and a pressure ring which are different in shape. When the pressure ring presses the seal ring, the support ring can cause the seal ring to come into shape and seal. When installing, the opening of the seal ring should face Pressure oil chamber; when adjusting the pressure ring, it should be limited to no leakage, and it must not be too tight to prevent excessive seal resistance.

If the sealing device is fitted with a sliding surface, it should be coated with an appropriate amount of hydraulic oil.

After the removal of the O-ring and dust ring should be completely replaced.



8) Special wrenches should be used when the threaded couplings are tightened, and the torque should meet the standard requirements.

9) After the piston is assembled with the piston rod, it is necessary to measure whether the coaxiality and the straightness over the entire length are excessive.



10)After assembly, the piston assembly should be free from blockage and uneven resistance.



11)When the hydraulic cylinder is installed on the mainframe, a seal ring must be added between the inlet and outlet port joints and fastened to prevent oil leakage.



12) After assembling as required, several reciprocating motions should be performed under low pressure to eliminate the gas in the cylinder.




Share to:  
Previous: Yangzhou Yinhe Machinery Co., Ltd. Next: 10 Steps Introductions of the Hydraulic Cylinder Design
Communicate with Supplier?Supplier
Rebecaa yin Ms. Rebecaa yin
What can I do for you?
Contact Supplier